Simrad SP90 - REV E Instrukcja Instalacji Strona 127
- Strona / 232
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Start-up procedures
115
851-164510 / Rev.E
Off centre
16 Check the Off centre function.
a Move the cursor to any position inside the echo area.
b Press the Off Centre button (field 8).
c Check that the ship’s symbol changes its position to
where the cursor is.
d Select Mode 2 and then Mode 1 to move the ship
symbol back to the screen centre.
Training
17 Check the Training function.
a Press the left and right Manual train buttons
repeatedly (field 9, right two buttons).
b Check that the white audio line on the screen trains
correspondingly.
c Try both directions.
18 Check the Position Track function.
a Move the cursor to any position on the screen.
b Press the Position Track button (field 9).
c Check that a circle appears at the cursor, and that the
audio line moves to the circle.
19 Check the Target Track function.
a Move the cursor to an echo.
b Press the Target Track button (field 9).
c Check that a violet circle appears at the cursor, and that
the audio line moves to the circle.
20 Check the Manual train function.
a Press the Manual training button (field 9).
b Check that the violet circle disappears.
21 Check the Auto search function.
a Press the Auto Search button (field 9).
b Check that the audio line starts a search within the
displayed sector limits.
c Press the Manual buttontostopthesearch.
- Installation manual 1
- Low frequency long range 3
- About this document 4
- Sections 5
- 12 Technical specifications 6
- 13 Drawing file 6
- High voltage safety warning 10
- 1INTRODUCTION 13
- 1.2 System diagram 14
- 1.3 Scope of supply 16
- Hull Unit 17
- Installation trunk 17
- Display unit 17
- 1.4 Peripheral equipment 19
- 1.5 Supply conditions 21
- 1.6 General safety rules 22
- Related topics 24
- 1.8 Equipment handling 25
- Initial preservation 26
- Inspection and unpacking 28
- After use storage 31
- Re-packing 33
- ESD precautions 34
- Temperature protection 35
- 2 INSTALLATION PLANNING 36
- 2.2 Location of the Hull Unit 37
- Fore and aft 37
- Athwartships 37
- Important considerations 38
- 2.3 Sonar room requirements 39
- Installation planning 41
- Figure 1 Sonar room 41
- 3SONARTRUNK 43
- 3.2 Mounting the trunk 44
- 3.3 Protection 45
- 3.4 Principles 46
- Sonar trunk 47
- Millimetres Inches 49
- 4HULLUNIT 50
- SP90 / SP92 SP91 / SP93 51
- 4.3 Unpacking 52
- 4.4 Mounting 53
- 4.5 Bleeding air 54
- 4.6 Mechanical support 55
- 4.7 Transducer alignment 56
- 4.8 Installation check-list 57
- 5 TRANSCEIVER UNIT 58
- 5.2 Installation procedure 59
- 5.3 Transceiver Unit drawings 60
- Transceiver unit 61
- 6 WHEELHOUSE UNITS 63
- 6.2 Location 64
- Sonar Operating Panel 65
- SonarProcessorUnit 65
- Loudspeaker 66
- 6.3 Display unit 67
- 6.4 Sonar Operating Panel 68
- Computer assembly 69
- Mounting frame 69
- Fastening screwsLocking pin 69
- 6.6 Sonar Interface Unit 70
- 6.7 Loudspeaker 71
- 7 CABLE LAYOUT 72
- 7.2 System cabling 73
- Cable layout 73
- System and shipyard cables 73
- 7.3 SP90 Cable plan 74
- Figure 15 SP90 Cable plan 75
- 7.4 Cable specifications 76
- 7.5 Wheelhouse cabling 79
- Connections 80
- C2 - Display cable 81
- C5 - Sonar Interface Serial 83
- - Operating panel (USB) 84
- 7.6 Sonar room cabling 87
- C17 - Motor control 88
- Figure 22 89
- Connections to the 89
- Motor Control Unit 89
- C16 - Transducer cable 94
- 7.7 Cable details 95
- Cable trays 96
- Radio Frequency interference 97
- Physical protection 97
- Grounding 97
- Cable connections 98
- Cable terminations 98
- Cable identification 98
- 8 PERIPHERAL EQUIPMENT 99
- Simrad SP90 100
- 8.2 Speed log connection 101
- References 102
- 8.3 Course gyro connection 103
- 8.4 (D)GPS connection 104
- 8.5 Echo sounder connection 105
- 8.6 Trawl system connection 106
- 8.8 Current meter 108
- 8.9 Radio buoys 109
- 9 START-UP PROCEDURES 111
- 851-164510 / Rev.E 113
- Supply voltage (Vac): 114
- 9.4 Starting up the Hull Unit 115
- Functional check 116
- (CD6350B) 117
- Apply 3-phase AC power 118
- Re-wire for 230 Vac 3-phase 118
- Functional check with power 119
- Introduction 121
- Start up 121
- Display set-up 122
- Functional test 124
- Horizontal gain and range 125
- Vertical gain and range 125
- Off centre 127
- Training 127
- Power off 128
- Preparations 129
- Checking the bridge functions 130
- Blank page 133
- → Connecting C15, page 101 136
- 9.9 Self-noise test 137
- 9.10 System start-up 138
- Actions on the bridge 139
- Actions in the sonar room 141
- Ship dimensions 146
- Instrument position offsets 146
- 10.1 Introduction 148
- 10.2 Interface settings 149
- Serial line inspection 150
- 10.3 Speed log 152
- Speed data from (D)GPS 153
- 10.4 Course gyro 154
- Heading data from (D)GPS 155
- 10.5 (D)GPS 156
- 10.6 Echo sounder 157
- 10.7 Trawl system 158
- 10.8 Catch monitoring system 159
- 10.9 Radio buoy system 160
- 10.10 Current meter system 161
- 11.1 Introduction 162
- Test procedure 164
- Measurement termination 167
- Procedure 168
- 11.4 Noise/speed curve 171
- Problems with flow noise 172
- Figure 43 Noise speed plot 174
- 12 TECHNICAL SPECIFICATIONS 175
- 12.2 Power specifications 176
- 12.3 Weights and dimensions 177
- 12.5 Telegram formats 180
- NMEA 0183 181
- Heading, magnetic 182
- Heading, true 182
- Speed log 183
- Time and date 184
- Trawl systems 185
- Trawl door spread 187
- Trawl Spread 2 187
- Trawl filling 187
- Trawl to shoal distance 188
- ITI Outputs 189
- FS900 Trawl system 189
- Depth of trawl below surface 189
- Osbbbbbb bbbbbbbb 190
- Geographical position 191
- Echo sounder 193
- Sea current sensor 195
- Wind sensor 196
- Technical specifications 197
- 13 DRAWING FILE 198
- Drawing file 199
- Control and Serial 200
- C6 - Cheapernet communication 201
- Sonar Interface Unit 202
- Serial lines 203
- Pulse speed log 204
- Transceiver Unit interface 205
- Synchronization 206
- Standard AC power cable 208
- AC 3-phase mains to Hull Unit 209
- Standard VGA cable 211
- Standard USB cable 212
- Operator panel 213
- SP92/93 Optional trunk 223
- 14 INSTALLATION REMARKS 225
- E 2005 Simrad AS 230
- ISBN-10: 82-8066-001-1 230
- ISBN-13: 978-82-8066-001-5 230
Powiązane produkty i podręczniki dla Nie Simrad SP90 - REV E
Nie Simrad AP25 Instrukcja Użytkownika
(192 strony)
(192 strony)
Nie Simrad NSS7 Instrukcja Użytkownika
(12 strony)
(12 strony)
Nie Simrad SP60 - REV D Instrukcja Instalacji
(218 strony)
(218 strony)
Nie Simrad SD570 Instrukcja Instalacji
(128 strony)
(128 strony)
Nie Simrad FS70 - REV 3 Instrukcja Instalacji
(110 strony)
(110 strony)
Nie Simrad SH80 - REV C Instrukcja Instalacji
(176 strony)
(176 strony)
Nie Simrad SP270 Instrukcja Instalacji
(254 strony)
(254 strony)
Nie Simrad 38-9 - REV B Instrukcja Instalacji
(202 strony)
(202 strony)
Nie Simrad SH90 - REV B Dokumentacja
(44 strony)
(44 strony)
Nie Simrad 50-200 COMBI C - REV D Instrukcja Obsługi
(112 strony)
(112 strony)
Nie Simrad AP26 Instrukcja Użytkownika
(6 strony)
(6 strony)
Nie Simrad FS25 Instrukcja Użytkownika
(8 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji