Simrad NSS Przewodnik Instalacji Strona 18
- Strona / 66
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
18
|
Connecting power | NSS Installation Manual
Connecting power
Power connection (basic)
The NSS display can be powered by either 12 V
or 24 V DC. Displays are protected against reverse
polarity, under voltage and over voltage.
The supplied power cable has a four core cable
used for:
• power into the system (Red and Black wires)
• controlling power state of the display or power
state of other displays and devices (Yellow wire)
• connecting to an external alarm (Blue wire)
Connect red to (+) DC using a 5 amp fuse for NSS12, and a 3 amp fuse for NSS7 and NSS8.
Connect Black to (-) DC. The display can be powered on and o using the power button.
Power Control (yellow wire)
Planning is required how you want to be able to turn on and o the NSS an connected com-
patible devices.
The yellow (Power Control) wire on the NSS power cable can either be an input that will turn
on the display when power is applied, or an output that turns on other devices when the
display is powered on. It can be con gured at the installation stage to control the power state
of displays and compatible devices. When commissioning the system, displays can be set to
be a Power Control Slave or Power Control Master.
Power Control con guration options of the NSS are:-
• use the Power button to turn on the display only: Yellow wire not connected
• display to turn on when power is applied to the display: Common red and yellow wires
• use the Power button to turn on the display and other displays and or compatible devices
such as Broadband Radar: Yellow wire connected to a Power Control Bus. (Set one or more
displays to be a Power Control Master)
12 - 24 V DC
Red (FUSE)
Black
Yellow
No Connect
+
_
Blue
12 - 24 V DC
Red (FUSE)
Black
Yellow
Blue
+
_
No Power Control
Yellow Wire: No Connect:
Display will turn on and o when the
power button on the front of the unit is
pressed. Power Control wire is not attached.
Auto Power on
Display will turn on when power is applied
to the display. Common the yellow wire with
the red wire after the fuse.
Note: The unit can not be powered down
but can enter a standby mode. (screen back-
light o ).
4
12 - 24 V DC
Red (FUSE)
Black
Yellow
No Connect
+
_
Blue
- Installation Guide 1
- NSS Installation Manual 2
- Copyright 3
- Warranty 3
- Declarations and conformance 3
- Compliance Statements 3
- About this manual 4
- Contents 5
- NSS overview 7
- Front - Controls 8
- Rear - Connectors 9
- NSS7 or NSS8 10
- NSS12 NSS12 11
- Planning the installation 12
- Check the contents 13
- Mounting location 14
- Mounting the NSS display 15
- Bracket mount 16
- Wiring the NSS 17
- Connecting power 18
- Power Control setup 19
- External alarm 20
- External Alarm Setup 20
- Echosounder 22
- Transducer adapter cables 23
- Echosounder software version 24
- T r ansducer type 25
- SimNet Network 26
- HD radar 27
- Scanner type 28
- Software version 28
- Serial Number 28
- MARPA status 28
- Reset device ID 28
- Sidelobe suppression 29
- Video In 30
- NMEA0183 31
- Serial port setup 32
- NMEA2000 / SimNet 33
- Mico-C to SimNet 34
- SimNet power 34
- SimNet terminator 34
- SimNet backbone 35
- SimNet drop cable 35
- SimNet power cable 36
- SimNet Terminator 36
- Ethernet to SimNet: 37
- NMEA 2000 / SimNet setup 38
- Ethernet (NETWORK port) 39
- Transducer 40
- Broadband Radar 40
- Databases 41
- IP addresses 41
- Module network light 41
- Autopilot 42
- Using the SG05 EVC gateway 43
- Autopilot setup 43
- Dockside setup 44
- Drive voltage 45
- Drive engage 45
- Motor output 45
- Rudder deadband 45
- STBY/AUTO key 45
- Compass calibration 46
- Compass mounting o set 46
- LUBBER LINE 46
- Autotuning 47
- Seastate lter 47
- Navigation change limit 50
- CZone connection to SimNet 51
- CZone setup 52
- Applying Software Updates 53
- Dimensioned Drawings 55
- 12 mm (0.47") 56
- 2.3 mm (0.09") 56
- 41 mm (1.61" 56
- 41 mm (1.61") 56
- Connector Pinouts 58
- NMEA2000 59
- Network (Ethernet) 59
- Accessory cables 60
- Supported data 61
- NMEA2000 PGN (transmit) 63
- NMEA0183 supported sentences 64
- Speci cations 65
- *988-10107-001* 66
Powiązane produkty i podręczniki dla Nawigatory Simrad NSS
Nawigatory Simrad AP28 Informacje Techniczne
(124 strony)
(124 strony)
Nawigatory Simrad NSS Przewodnik Instalacji
(23 strony)
(23 strony)
Nawigatory Simrad CX54-DE Instrukcja Operatora
(118 strony)
(118 strony)
Nawigatory Simrad HH36 Instrukcja Użytkownika
(88 strony)
(88 strony)
Nawigatory Simrad HH36 Instrukcja Użytkownika
(88 strony)
(88 strony)
Nawigatory Simrad NSS7 Instrukcja Instalacji
(96 strony)
(96 strony)
Nawigatory Simrad AC42 Informacje Techniczne
(116 strony)
(116 strony)
Nawigatory Simrad AP26 Instrukcja Użytkownika
(148 strony)
Nawigatory Simrad MX525A Dokumentacja
(34 strony)
(34 strony)
Nawigatory Simrad MX525A Dokumentacja
(34 strony)
(34 strony)
Nawigatory Simrad AP50 Dokumentacja
(62 strony)
(62 strony)
Philips 10001436 manuales
Manuales del propietario y guías del usuario para Para Casa Philips 10001436.
Ofrecemos 1 manuales en pdf Philips 10001436 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji